اشتراک در خبرنامه
لطفاً نشانی پست الکترونیک خود را برای دریافت اطلاعات و اخبار پایگاه در کادر زیر وارد کنید.
آمار سایت
- کل کاربران ثبت شده: 1963 کاربر
- کاربران حاضر در وبگاه: 0 کاربر
- میهمانان در حال بازدید: 205 کاربر
- تمام بازدیدها: 22233580 بازدید
- بازدید ۲۴ ساعت گذشته: 3378 بازدید
کنفرانس های انجمن
همایش
اپتیک و فوتونیک،
بهمن 1403
(برگزار شد)
استفاده از مطالب ارائه شده در این پایگاه با ذکر منبع آزاد می باشد.
سال 28، شماره 1 - ( مجموعه مقالات پذیرفته و ارائه شده در اولین کنفرانس ملی حسگرهای فیبر نوری 1400 )
ICOP & ICPET _ INPC _ ICOFS سال28 صفحات 36-34 |
برگشت به فهرست نسخه ها
Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:



Tamimi A, Ghezelayagh M, Bashiri A. Design and construction of visible light Instantaneous wavelength measurement. ICOP & ICPET _ INPC _ ICOFS 2021; 28 (1) :34-36
URL: http://opsi.ir/article-1-2502-fa.html
URL: http://opsi.ir/article-1-2502-fa.html
Tamimi Ali، Ghezelayagh Mohammdhossein، Bashiri Abbas. Design and construction of visible light Instantaneous wavelength measurement. مقالات پذیرفته و ارائه شده در کنفرانسهای انجمن اپتیک و فوتونیک ایران. 1400; 28 (1) :34-36
1- Faculty of EE, Imam Hossein University, Tehran, Iran
چکیده: (1005 مشاهده)
This paper presents a method for measuring the wavelength of visible light. Many laboratory and industrial applications require a wavelength measurement system. Wavelength sensing devices in the visible and infrared spectrum are expensive and bulky. As a result, the use of wavelength sensors has been neglected in many applications. In this research, a practical design and construction of a wavelength measuring device with a simple electro-optical method has been investigated. Cost is much lower than the existing spectrometers, portability and continuous output are the features of this system. The system's response range is from 750 to 950 nm. Increasing wavelength spectral range is possible using a different optical filter. The key to solving the problem is the unique amount of light passing through a filter for a specific wavelength. When the signal reaches the system with a specific wavelength, as the amount of input light attenuation is a unique for each wavelength, the wavelength (frequency) of the received signal can be determined by the amount of light attenuation in comparison to reference light. Then the wavelength can be declared by a processor. Depending on the measured wavelength, color detection can be done based on the wavelength.
واژههای کلیدی: Instantaneous frequency measurement، Wavelength measurement، Frequency measurement، Spectrometry
بازنشر اطلاعات | |
![]() |
این مقاله تحت شرایط Creative Commons Attribution-NonCommercial 4.0 International License قابل بازنشر است. |